26 Online
2 Member And 24 Guest
Members present at the site
Today Visits : 4609
Yesterday Visits : 8142
All Visits : 925861

Welcome to Electronoobs Q&A, where you can ask questions and receive answers from other members of the community.



Categories


1 like 0 dislike


IDE
Arduino 1.8.7

Nano: Nano board blink prog., built in, works

 but cant get even basic blink file to upload:-

avrdude: Version 6.3-20171130

         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/

         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is "C:\Program Files\Arduino\hardware\tools\avr/etc/avrdude.conf"

         Using Port                    : COM19

         Using Programmer              : arduino

         Overriding Baud Rate          : 115200

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x42

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x42

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x42

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x42

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x42

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x42

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x42

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x42

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x42

avrdude: stk500_recv(): programmer is not responding

avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x42

avrdude done.  Thank you.

Problem uploading to board. 




HELP!!


I am a newbie surprise.

also,

Cant find how donate!!

in Arduino by (130 points)
edited by

1 Answer

0 like 0 dislike
Do you have anything connected to the TX and RX pins while programming? It looks like the Arduino can't be reached and it can be for 2 things: you have something connected to TX and RX pins or the Arduino is damaged.
by (34.8k points)

pls see my email reply to this, sent just now, , certainly not related to TX/Rx pins.

emailed:  it programs when i select the old bootloader,, AND it doesnt seem to care re the  "Programmer" selection in 'Tools'..

 - I tried various choices, it didn't seem to make a difference! The default seemed to be USBTiny ISP

  • What should it be set to?

  • Can I please have a photo of the loaded pcb, as made for the CNC project.

Its a pity that the .png of the schematic just has lots of node points, & not the full schematic, wired pin to pin;
I can reverse engineer the pcb but would prefer the easier / quicker solution of a full schematic,
preferably the actual schematic file.

  • Can I please have a photo of the loaded pcb, as made for the CNC project. Its a pity that the .png of the schematic just has lots of node points, & not the full schematic, wired pin to pin; I can reverse engineer the pcb but would prefer the easier / quicker solution of a full schematic, preferably the actual schematic file.
  • Could you please post, for all concerned, a photo of the loaded pcb, as made for the CNC project.
  • Its a pity that the .png of the schematic just has lots of node points, & not the full schematic, wired pin to pin; If i am understanding the .png schematic, why does the Dir_Y pin on U2, the LCD Nano, seem to be wired to the Dir Y pin on the Motor Nano, U1, pin9 (D6) ? (and then this junction wired to the driver chip, A4988).
    [I can reverse engineer the pcb but would prefer the easier / quicker solution of a full schematic, preferably the actual schematic file].
  •  

my above texts seems to have multiple duplications.

I would like to add that i get it now re Dir pins wired to LCD.. to subtract or add to the mm travel count. Wasn't readily apparent! If i could understand this strange code stuff i'd be more 'in the know'.

[History: Analogue Tech work, with basic digital repairs, tiny bit of assembler on old 6800 - "AISZ"!! ].
...